6226 NKE Deep Groove Ball Bearings

D:70 mm; Coefficient of friction µ max.:0.15; Tolerance shaft:f7 m/s; Permissible sliding velocity v max.:1 m/s; B:55 mm; Specific static load factor K0:120 N/mm²; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7 m/s; Mass bushing:0.26 kg; Specific dynamic load factor K:40 N/mm²;

rc max.:0.6 mm; C:66 mm; Mass bearing pair:6.48 kg; d:110 mm; Calculation factor Y1:1.6; D:170 mm; T:84 mm; Reference speed:2400 r/min; Calculation factor Y2:2.3; Cb min.:9 mm;

da:101.6 mm; Adapter sleeve assembly:SNW 3024x4; P90°:84.5 kN; A1:111.125 mm; Mass pillow block:39.5 kg; Da:180 mm; H2:44.45 mm; Cap bolt, SAE grade:8; Ca:55.804 mm; Cap bolt recommended tightening torque:298.3 N·m;

Accessories:Two Shields & Snap-R; Grease Speed Rating n1:16000 rpm; Basic Static Radial Load Rating Co:6550 N; Oil Speed Rating Open/Shielded n2:19000 rpm; Oil Speed Rating n2:19000 rpm; B:14.00 mm; Grease Speed Rating Open/Shielded n1:16000 rpm; Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:11000 rpm; d:17.000 mm;

Grease Speed Rating n1:16000 rpm; Basic Dynamic Radial Load Rating C:13500 N; Accessories:One Seal; B:14.00 mm; D:47.0000 mm; Sealed Speed Rating n3:11000 rpm; d:17.000 mm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:6550 N; Oil Speed Rating n2:19000 rpm;

Da min.:1063 mm; α:2 °; ra max.:3 mm; rb max.:7.5 mm; C:600 mm; d:900 mm; r1 min.:3 mm; Material constant KM:1055; Design (sliding contact surface combination):Steel/PTFE FRP; r2 min.:7.5 mm;

Basic Static Radial Load Rating Co:1750 lbf; Width A:1.3750 in; Insert Bearing IB:ZMaRC; Shaft Diameter D:15/16 in; Pin Dia A1:0.5313 in; Dimension G:0.4375 in; Dimension B:3.6250 in; Dimension J:1.4375 in; Weight W:0.92 lb; Dimension N:0.6563 in;

D:70 mm; Coefficient of friction µ max.:0.15; Tolerance shaft:f7 m/s; Permissible sliding velocity v max.:1 m/s; B:55 mm; Specific static load factor K0:120 N/mm²; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7 m/s; Mass bushing:0.26 kg; Specific dynamic load factor K:40 N/mm²;

Basic Static Radial Load Rating Co:216000 N; Fillet Radius ra:2.00 mm; D:160.0000 mm; Basic Dynamic Radial Load Rating C:203000 N; Oil Speed Rating n2:5400 rpm; B:60.00 mm; Grease Speed Rating n1:3800 rpm; d:90.000 mm; Fillet Radius rb:1.00 mm;

J max.:311.15 mm; Basic dynamic load rating C:426 kN; J min.:254 mm; H:213.519 mm; S:0.794 mm; H2:63.5 mm; da:101.6 mm; L:361.95 mm; B:80.169 mm; s:38.497 mm;

B5:73.812 mm; B:60.579 mm; d3 max.:520.827 mm; d:440 mm; Hydraulic nut:HMVC 88E; Locking plate:PL 88; Threads per inch:5; G:438.988 mm; Sleeve:S 3288x16.1/2; d1:419.1 mm;

J max.:311.15 mm; Basic dynamic load rating C:426 kN; J min.:254 mm; H:213.519 mm; S:0.794 mm; H2:63.5 mm; da:101.6 mm; L:361.95 mm; B:80.169 mm; s:38.497 mm;

Da min.:1063 mm; α:2 °; ra max.:3 mm; rb max.:7.5 mm; C:600 mm; d:900 mm; r1 min.:3 mm; Material constant KM:1055; Design (sliding contact surface combination):Steel/PTFE FRP; r2 min.:7.5 mm;

D1:72 mm; r1,2 min.:1.1 mm; D:125 mm; B:12 mm; Mass housing washer:0.79 kg;

Grease Speed Rating n1:16000 rpm; Basic Dynamic Radial Load Rating C:13500 N; Accessories:One Seal; B:14.00 mm; D:47.0000 mm; Sealed Speed Rating n3:11000 rpm; d:17.000 mm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:6550 N; Oil Speed Rating n2:19000 rpm;