Bantalan 32964 ISO

Specific static load factor K0:20 N/mm²; D:5 mm; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; B1:1.5 mm; Tolerance shaft:h8; Coefficient of friction µ min.:0.05; Tolerance housing:H7; B:4 mm; d:3 mm;

Grease Speed Rating n1:2000 rpm; d:100.000 mm; Oil Speed Rating n2:3000 rpm; B:60.30 mm; Sealed Speed Rating n3:2000 rpm; D:180.0000 mm; Basic Static Radial Load Rating Co:166000 N; Fillet Radius ra:2.00 mm; Accessories:Shield & Seal; Basic Dynamic Radial Load Rating C:178000 N;

Grease Speed Rating n1:2000 rpm; d:100.000 mm; Oil Speed Rating n2:3000 rpm; B:60.30 mm; Sealed Speed Rating n3:2000 rpm; D:180.0000 mm; Basic Static Radial Load Rating Co:166000 N; Fillet Radius ra:2.00 mm; Accessories:Shield & Seal; Basic Dynamic Radial Load Rating C:178000 N;

Accessories:8000 One Seal; Width - Outer Ring B0:8.0 mm; Basic Interchange FAF:38KL; D:22.0000 mm; Old MRC Bearing Number:38FS1; d:8.000 mm; Basic Radial Load Rating-Static SCO:1370 N; Width - Overall B:10.3 mm; Width - Inner Ring B1:9.80 mm; Speed Rating-Single and Double Sealed Grease SDG:23000 rpm;

Minimum load factor A:220; ra max.:4 mm; d1 ≈:644 mm; d:480 mm; Limiting speed:560 r/min; Basic dynamic load rating C:995 kN; Mass bearing (including seat washer where applicable):130 kg; da min.:581 mm; Fatigue load limit Pu:102 kN; D:650 mm;

Specific static load factor K0:20 N/mm²; D:5 mm; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; B1:1.5 mm; Tolerance shaft:h8; Coefficient of friction µ min.:0.05; Tolerance housing:H7; B:4 mm; d:3 mm;

Sealed Speed Rating n3:9500 rpm; Oil Speed Rating Open/Shielded n2:18000 rpm; d:25.000 mm; Basic Static Radial Load Rating Co:6550 N; B:12.00 mm; Fillet Radius ra:0.64 mm; Basic Dynamic Radial Load Rating C:11200 N; Grease Speed Rating Open/Shielded n1:15000 rpm; Accessories:Two Seals & Snap-Rin; D:47.0000 mm;

Specific static load factor K0:20 N/mm²; D:5 mm; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; B1:1.5 mm; Tolerance shaft:h8; Coefficient of friction µ min.:0.05; Tolerance housing:H7; B:4 mm; d:3 mm;

Specific static load factor K0:20 N/mm²; D:5 mm; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; B1:1.5 mm; Tolerance shaft:h8; Coefficient of friction µ min.:0.05; Tolerance housing:H7; B:4 mm; d:3 mm;

Dimension H2:16.5 mm; Height H:82.0 mm; Shaft Diameter D:30 mm; Weight W:1.30 kg; Dimension S1:22.2 mm; Basic Dynamic Radial Load Rating C:19500 N; Insert Bearing IB:ZMaRC; Dimension H1:42.9 mm; Width A:40.0 mm; Dimension N:23.5 mm;

Dynamic (Ca):619 kN; Static (Coa):708 kN; b1:26 mm; d2:140 mm; D:300 mm; d2 (max):198.4 mm; E:mm; rs (min):4 mm; b:15 mm; s:2.7 mm;

Taconite seal:TER 44; Initial grease fill:87.885 g; S:4.763 mm; Cap bolt:2 x 5/8-11 UNC; da:68.263 mm; P120°:49.8 kN; J max.:279.4 mm; P60°:138 kN; R1:53.181 mm; L:330.2 mm;

B1:109 mm; Lock nut:KML 36; Hydraulic nut:HMV 36 E; Mass adapter sleeve assembly:5.55 kg; d1:165.1 mm; d:180 mm; G:M 180x3; Locking device:MBL 36; d3:210 mm; B:27 mm;

Dynamic (Ca):619 kN; Static (Coa):708 kN; b1:26 mm; d2:140 mm; D:300 mm; d2 (max):198.4 mm; E:mm; rs (min):4 mm; b:15 mm; s:2.7 mm;

Specific static load factor K0:20 N/mm²; D:5 mm; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; B1:1.5 mm; Tolerance shaft:h8; Coefficient of friction µ min.:0.05; Tolerance housing:H7; B:4 mm; d:3 mm;